How Much Should My Solar Panels Produce Each Month in Alberta?

Your installer handed you a production estimate, your inverter app shows a number every day, and your power bill shows something else entirely. So how do you know whether your solar system is actually doing its job? The honest answer is that one month on its own tells you very little. Alberta solar output swings hard with the seasons, so a December that looks alarming can be perfectly normal, and a June that looks fine can hide a failed panel.

This guide gives you month-by-month production benchmarks for Calgary, Edmonton and Fort McMurray, explains why your real numbers will differ from any model, and walks through the checks that tell a normal dip apart from a real problem.

The short answer: a south-facing, unshaded system in Alberta makes very roughly 1,050 to 1,250 kWh per kW of panels a year, and about two-thirds of that arrives between April and September. Compare each month with the same month last year, or with the benchmarks below, never with the month before.

Monthly Solar Production Benchmarks for Alberta

The table shows modelled production for each 1 kW of panels, facing due south at a 35° tilt, with 14% system losses. To estimate your own system, multiply by its size in kW. The figures come from the European Commission’s PVGIS solar calculator, which uses NREL’s satellite solar data for North America (retrieved October 2026).

Month Calgary (kWh per kW) Edmonton (kWh per kW) Fort McMurray (kWh per kW)
January 55 43 34
February 73 64 63
March 107 101 104
April 128 131 126
May 142 150 143
June 132 139 128
July 155 153 130
August 141 140 118
September 118 110 93
October 93 83 65
November 64 48 27
December 49 36 17
Year ~1,258 ~1,197 ~1,046

Example: a 7 kW system in Edmonton works out to roughly 1,070 kWh in July but only about 250 kWh in December, and around 8,400 kWh over a full year. All three cities make most of their power from April to September: about 65% of the year’s total in Calgary, 69% in Edmonton and 71% in Fort McMurray. November to February together supply only 13% to 19%.

Two things to keep in mind. First, the model assumes a clear panel surface. It does not account for snow, so real December and January numbers will be lower whenever your panels are buried. Second, these are typical-year figures. A smoky August or a cloudy June (June is often Calgary’s wettest month) can easily put a given month 10% to 20% off. In our own cost guides we use a more conservative 1,150 kWh per kW a year for exactly that reason. See the Alberta solar panel cost guide for how that figure is used in sizing.

Why Your Numbers Won’t Match the Model

A system that comes in below these benchmarks isn’t necessarily broken. These are the usual, legitimate reasons:

Orientation and tilt

East- and west-facing arrays make noticeably less than south-facing ones, and flat or very steep panels lose some output too. If your installer split panels across two roof faces, expect a blended result. Our guide to the best solar panel angle and orientation in Alberta explains the trade-offs.

Shade that grows

Trees grow. A spruce that cast no shadow in the year you installed can clip your morning production five years later, and the effect is largest in spring and fall when the sun is lower. A neighbour’s new garage or second storey can do the same.

Snow

Snow cover can stop production completely until it slides or melts off. That is expected, and climbing onto an icy roof to clear it is rarely worth the risk. Our winter solar guide covers what to expect.

Normal ageing

Panels slowly lose output. A review of nearly 2,000 field measurements by the U.S. National Renewable Energy Laboratory found a median degradation rate of about 0.5% per year (Jordan and Kurtz, NREL). After ten years, that is roughly 5%: noticeable on paper, not something you would see month to month. Your panel warranty guarantees a minimum output over time; our solar warranty guide explains how to read it.

How to Check Your Solar Production Properly

  1. Convert to kWh per kW. Divide your monthly production by your system size. That lets you compare directly against the table above, and against friends or neighbours with different-sized systems.
  2. Compare year over year. This July versus last July is the most useful comparison you have. A steady difference of a few percent is weather. A sudden drop of 15% or more in a sunny month deserves a closer look.
  3. Check your installer’s estimate. Most quotes include a modelled annual production figure for your specific roof. Measure your full-year total against that, not against a generic benchmark.
  4. Look at a sunny day’s curve. In your inverter or monitoring app, a clear day should draw a smooth hill: rising after sunrise, peaking around solar noon, falling toward evening. A flat top on the brightest days is clipping: the inverter capping output, which is normal on many systems. A notch at the same time every morning is usually shade. A curve that is half its normal height suggests part of the array has stopped working.
  5. If you have microinverters or optimizers, compare panels. Panel-level monitoring shows each module side by side. One panel consistently well below its neighbours usually means a failed microinverter, a damaged panel or a loose connection.

Red Flags That Mean Something Is Wrong

  • Zero production on a clear day, with no snow on the panels. Check the solar breaker in your electrical panel and any outdoor disconnect switch, then look at the inverter’s status light or screen.
  • An error or fault light on the inverter, or a fault notice in the app.
  • A step change: output drops sharply from one week to the next and stays down, especially after a hailstorm, a power outage or electrical work in the house.
  • One panel or one string far below the rest on panel-level monitoring.
  • The app shows nothing at all but the inverter’s own screen shows production. This is usually a monitoring problem, not a solar problem. A new router or a changed WiFi password is the most common cause: the inverter or gateway has simply lost its internet connection and needs to be reconnected.

After hail, document production before and after the storm and photograph the array from the ground. Our hail and insurance guide lists what your insurer will ask for.

Your Inverter App and Your Bill Measure Different Things

This is the single most common source of confusion. Your inverter app counts every kilowatt-hour your panels produce. Your bi-directional meter, and therefore your bill, only counts power that crosses the meter: what you bought from the grid and what you exported to it. The solar you used in your own home in real time never appears on the bill at all, even though it is the reason the bill is smaller.

So if your app says 1,000 kWh for the month and your bill shows 600 kWh exported, the other 400 kWh weren’t lost; you used them. Billing periods also rarely line up with calendar months, which makes the two even harder to compare. Our guide on how to read a solar micro-generation bill walks through every line.

If you’re a Get Energy Solar Club® member, SunLedger™, our online portal, lines up your production with each billing period, so you can see what you made, used, exported and earned in one place. Production data can be connected for systems whose inverter or monitoring platform allows it.

Who to Call When Something Looks Off

  • Your installer for low production, fault codes, failed panels or inverters, and anything under the equipment or workmanship warranty. If your installer has closed, contact the manufacturer directly about the product warranty. See our maintenance guide for what you can safely check yourself first.
  • Your wires company (FortisAlberta, ATCO Electric, ENMAX Power or EPCOR, depending on where you live) for meter problems, such as exports never showing up after the system was energized. Not sure which one serves you? See who is my wires company?
  • Your retailer if production looks normal but your export credits don’t, or if you aren’t sure your plan is crediting exports the way you expected.

Production Is Half the Story: What Your Exports Earn

Under Alberta’s micro-generation rules, power your panels send to the grid is credited on your bill at your plan’s energy rate for that period. That makes your plan as important as your panels, especially in the April-to-September months when most Alberta solar homes become net exporters.

The Solar Club® is a loyalty program for Alberta solar micro-generators from UTILITYnet (Utility Network & Partners Inc.); Get Energy offers it as a partner retailer. Members are on one of two Solar Club® rates: the HI Rate, for periods when you export more than you import, and the LO Rate, for periods when you import more than you export. On the LO side you choose either the fixed LO Rate or the variable rate. Whichever rate you are on applies to both the power you import and the power you export in that period. With RateSwitch™ turned on, you are moved between HI and LO automatically whenever your Pre-Bill™ data shows your net status flip between importer and exporter, so there is nothing to time yourself. Rates change, so this guide doesn’t list them: see the current HI and LO Rates or the Solar Club® page.

With Get Energy, your Solar Club® export credits carry forward on your account. Once your credit balance reaches $200 we pay it out, or, if you prefer, we can pay out monthly, or leave the credit on your account to cover your winter bills. To see how the Solar Club® compares with other options, read our solar export rate comparison.

Turn Your Production Into a Payback Number

We don’t print a payback figure here, because it depends on electricity rates and rates change. Once you know your real production, the math is simple:

  • Annual value = (kWh you use at home × your all-in energy rate) + (kWh you export × your plan’s rate for that period)
  • Simple payback in years = installed cost ÷ annual value

Your app gives you total production and your bills give you exports; the difference is what you used at home. Plug in today’s figures from our rates page, and see are solar panels worth it in Alberta? for a longer walk-through.

Frequently Asked Questions

How much should my solar panels produce each month in Alberta?

Per kW of south-facing panels, modelled production ranges from about 36 to 55 kWh in December and January up to about 150 kWh in May and July for Calgary and Edmonton (PVGIS, typical year, no snow). Multiply by your system size in kW. Fort McMurray is similar in spring and summer but much lower from November to January.

How many kWh does a solar panel system produce per year in Alberta?

A south-facing, unshaded system typically produces about 1,050 to 1,250 kWh per kW of panels a year, depending on location, tilt, shading and snow. Get Energy uses a conservative 1,150 kWh per kW for planning. A 7 kW system therefore makes roughly 8,000 kWh a year.

Why is my solar production so low in winter?

Short days, a low sun angle and snow cover. In Calgary, Edmonton and Fort McMurray, November to February together supply only about 13% to 19% of a typical year's production, while April to September supplies about two-thirds. Low winter output is normal; compare each month with the same month last year.

Why doesn't my inverter app match my electricity bill?

Your inverter app counts everything your panels produce. Your bill only counts power that crosses the meter: what you bought and what you exported. Solar you used at home in real time never appears on the bill. Billing periods also rarely match calendar months.

How do I know if my solar panels are not working?

Warning signs include zero production on a clear, snow-free day, a fault light on the inverter, a sudden drop that stays down, or one panel far below the others on panel-level monitoring. If the inverter screen shows production but the app shows nothing, the monitoring connection has usually dropped, often after a router or WiFi password change.

Next Steps

Pull up the same month from last year in your monitoring app, convert it to kWh per kW, and compare it with the table above. If something looks off, start with the breaker, the inverter status light and your WiFi connection, then call your installer. Thinking about solar but not there yet? Our sizing guide and installer guide are good places to start, and city guides for Calgary, Edmonton and Fort McMurray cover local costs and permits.

Already producing? See how the Solar Club® works for solar homes, check the current rates, and sign up online in a few minutes. There is no cancellation fee, and you can keep your installer and equipment.

Solar Club® is a loyalty program of Utility Network & Partners Inc. (UTILITYnet); Get Energy is a partner retailer and a tradename of Utility Network & Partners Inc. Rates change: see current rates. Production figures are modelled estimates from PVGIS (European Commission JRC) and are not a guarantee of any system’s output.